Numerical Investigation of the Effect of Geometry on the Energy Absorption Rate of Sandwich Panels under Blast Loading

Document Type : Original Article

Authors

Imam Hossein University

Abstract

In the recent years, advent of new technologies in the field of Structural Engineering, elements such as Sandwich Panels has attracted more attention, which are lightweight and highly resistant.Sandwich components are  the most widely used elements to resist against the pressure of explosion wave. The core of the sandwich panels does the most important role in absorbing and dissipating the energy of the explosion.And geometric shape of the core can have a decisive role in the amount of energy absorption. Accordingly, in this paper, the effect of geometric shape of the core of the steel sandwich panel on its behavior and amount of energy absorption against the explosion wave is analyzed by numerical methods. Abaqusfinite element software is used for simulation and analyzing. Validation of the responses obtained from numerical solution was performed with experimental data of valid papers. In the following, sandwich panels with four different types of regular and easily fabricated cores, were modeled under different pressures of explosive wave. And the effect of core geometry on the amount of energy absorption and displacement was investigated.Two important criteria in designing these types of sandwich panels are maximizing energy absorption and minimizing maximum displacement. The results show that at low pressures Model 4 with a quadrilateral horizontal core has the maximum energy absorption and minimum displacement value. However, at high pressures Model 2 with a hexagonal vertical core has the minimum displacement and Model 1 with a quadrilateral vertical has the maximum energy absorption. In other words related to the explosion pressure, a sandwich panel with the special geometry can have the best performance.

Keywords

Main Subjects


[1]     Heimbs, S. “Foldcore Sandwich Structures and their impact Behaviour: an Overview”; Dynamic failure of composite and sandwich structures. Springer, Dordrecht, 2013.##
[2]             Gilkie, R.; Sundararaj, P. “The Impact Resistance of Plastics Sandwich Constructions using Low Density Urethane Foam Cores”; J. Cell. Plast. 1971, 7, 313-318.##
[3]     Nayak, S. K.; “Optimization of Honeycomb Core Sandwich Panel to Mitigate the Effects of Air Blast Loading”; MS. Thesis, The Pennsylvania State University, 2010.##
[4]             Nurick, G.; Martin, J. “Deformation of Thin Plates Subjected to impulsive Loading—a Review Part II: experimental Studies”; Int. J. Impact. Eng. 1989, 8, 171-186.##
[5]             Nurick, G.; Martin, J.  “Deformation of Thin Plates Subjected to Impulsive Loading—a Review: Part i: Theoretical Considerations”; Int. J. Impact. Eng. 1989, 8, 159-170.##
[6]             Rajendran, R.; Lee, J. “Blast Loaded Plates”; Mar. Struct. 2009, 22, 99-127.##
[7]             Jacob, N.; Yuen, S. C. K.; Nurick, G.; Bonorchis, D.;  Desai, S.; Tait, D.“Scaling Aspects of Quadrangular Plates Subjected to Localised Blast Loads—Experiments and Predictions”; Int. J. Impact. Eng. 2004, 30, 1179-1208.##
[8]             Xue, Z.;  Hutchinson, J. W. “Preliminary Assessment of Sandwich Plates Subject to Blast Loads”; Int. J. Mech. Sci. 2003, 45, 687-705.##
[9]             Mori, L.;Queheillalt, D.;Wadley, H.;Espinosa, H. “Deformation and Failure Modes of I-core Sandwich Structures Subjected to Underwater Impulsive Loads”; Exp. Mech. 2009, 49, 257-275.##
[10]          Valdevit, L.; Wei, Z.; Mercer, C.; Zok, F. W.; Evans, A. G.; “Structural Performance of Near-Optimal Sandwich Panels with Corrugated Cores”; Int. J. Solids. Struct. 2006, 43, 4888-4905.##
[11]          Jing, L.;Yang, F.;Wang, Z.;Zhao, L.“A Numerical Simulation of Metallic Cylindrical Sandwich Shells Subjected to Air Blast Loading”; Lat. Am. J. Solids Stru. 2013, 10, 631-645.##
[12]  Vatani Oskouei, A.;Kiakojouri, F.“Non-linear Dynamic Analysis of Steel Hollow I-Core Sandwich Panel under Air Blast Loading”; Civil. Eng. Civil. Infr. 2015, 48, 323-344.##
[13]  Peyman, S.;Ghazanfarinia, S.“Defence and Secutity Structures”; MAUT Press, 2007.##
[14]  Sayed M. Soleimani, Nader H. Ghareeb, Nourhan H. Shaker, Modeling, Simulation and Optimization of Steel Sandwich Panels under Blast Loading,  American Journal of Engineering and Applied Sciences, 2018.##
[15]  Sabzevari, S.; Shahabian, F. “Optimum Selection of Corrugated Sandwich Panels Shape and Materials Subjected to Blast Loading”.##
[16]  Peyman, S.;Sonbolestan, S.H.“Analysis of Underground Tunnels in Explosion Loading Based on Peak Particle Velocity”; Advanced Defence Sci. & Technol. 2017, 8, 45-50.##
[17]  Bulson, P. S. “Explosive Loading of Engineering Structures”; CRC Press: 2002.##
[18]  Brode, H. L. “Numerical Solutions of Spherical Blast Waves”; J. Appl. Phys. 1995, 26, 766-775.##
[19]  Henrych, J.; Major, R. “The Dynamics of Explosion and its Use”; Elsevier/North-Holland, Inc., New York, 1979.##
[20]  Dharmasena, K. P.; Wadley, H. N.; Xue, Z.; Hutchinson, J. W. “Mechanical Response of Metallic Honeycomb Sandwich Panel Structures to High-Intensity Dynamic Loading”; Int. J. Impact. Eng. 2008, 35, 1063-1074.##
Nahshon, K.; Pontin, M.; Evans, A.; Hutchinson, J.; Zok, F.; “Dynamic Shear Rupture of Steel Plates”; J. Mech. Mater. Struct. 2007, 2, 2049-2066. ##
Volume 11, Issue 4 - Serial Number 42
January 2021
Pages 347-355
  • Receive Date: 10 March 2019
  • Revise Date: 13 March 2020
  • Accept Date: 13 March 2020
  • Publish Date: 21 December 2020