@article { author = {مداح, بزرگمهر and داوودی, علی and خاکباز, محمد رضا}, title = {Investigation of X Frequency Microwave Absorbance of Ferrite Nano-Composite in Polyurethane Matrix}, journal = {Journal of Advanced Defense Science & Technology}, volume = {7}, number = {1}, pages = {1-8}, year = {2016}, publisher = {Imam Hussein University}, issn = {2676-2935}, eissn = {2980-8022}, doi = {}, abstract = {In modern battlefield, Radar has emerged as an important sensor to detect and target the military equipment of enemy. The camouflage against radar sensor is mainly achieved through the use of radar absorbing materials (RAM). These materials absorb most of the radar incident energy, thereby reducing the reflected signal to minima, and thus locking the capability of radar detection. In this study, the ability of different nanocomposites were examined to measure the reflection loss. Polyaniline, iron oxide and titanium oxide nanocomposite on Polyurethane substrate was successfully tested and absorbed good amount of radar waves. In order to optimize the reflected loss (the amount of absorbance), the effect of parameters such as thickness and concentration of nanocomposite were considered. The results indicated that the maximum loss in range of 8-12 GHz for a thickness of nanocomposite as 7.5 mm, is about 22.5 dB at 9.7 GHz .}, keywords = {Radar Absorbing,Nanocomposite,Titanium Oxide,Polyurethane,Fe3O4 Nano-Particle}, title_fa = {بررسی جذب امواج راداری در ناحیه فرکانسی X توسط نانوکامپوزیت فریتی در بستر پلی یورتان}, abstract_fa = {رادار به‌عنوان یک سیستم مهم در میدان جنگ مدرن برای تشخیص و از بین بردن توان نظامی دشمن مورد استفاده قرار می‌گیرد. استفاده از مواد جاذب رادار، یکی از روش‌های مرسوم در برابر حسگر راداری می‌باشد. این مواد، انرژی رادار را جذب می‌کند، تابش برگشت داده‌شده را کاهش می‌دهند و در نتیجه از شناسایی جلوگیری می‌کند. نانوکامپوزیت‌های مختلفی برای اتلاف امواج راداری، در این تحقیق آزمایش شد و از میان آن‌ها نانوکامپوزیت پلی آنیلین، نانواکسید آهن و نانواکسید تیتانیوم بر پایه پلی­یورتان با موفقیت تهیه شد. همچنین تأثیر ضخامت و درصد غلظت این نانوکامپوزیت‌ها بر میزان جذب امواج، مورد بررسی قرار گرفت. نتایج نشان داد که حداکثر افت انعکاسی که در محدوده فرکانسی 8-12 گیگاهرتز برای کمپوزیت با ضخامت 5/7 میلی‌متر برای فرکانس7/9 گیگاهرتز مشاهده می­شود، حدود 5/22 دسی‌بل است.}, keywords_fa = {جذب امواج رادار,نانوکامپوزیت,نانوذره تیتان,پلی‌یورتان,نانوذرات}, url = {https://adst.ihu.ac.ir/article_204170.html}, eprint = {https://adst.ihu.ac.ir/article_204170_05c15ba5cb9ed6e26550087b68ffd2de.pdf} } @article { author = {خزائی, صفا and کاظمی, محمد جواد}, title = {Modeling of Required Time to Reach the Maximum Phosgene Oxime Pollution in Runoff (Case Study: The Adjacent Areas of Kan River and North Flood Return of West Tehran)}, journal = {Journal of Advanced Defense Science & Technology}, volume = {7}, number = {1}, pages = {9-18}, year = {2016}, publisher = {Imam Hussein University}, issn = {2676-2935}, eissn = {2980-8022}, doi = {}, abstract = {Water pollution caused by chemical materials in different forms such as chemical bombs, terrorist attacks, and reluctant events is one of the main concerns of human societies. Chemical pollutions can permeate into surface waters because of the release of pollutions on the ground or rainfall in the time of air pollution. The main objective of this study is to model the surface water pollution reaching its maximum level after entering the chemical pollution. In this study, diffusion of chemical pollution caused by phosgene oxime (blister agent) in all areas alongside to Kan River and the reverse flood area of the west of Tehran is modeled using ArcGIS and SWMM softwares. Based on the results, the maximum density of pollution depends on the return period of rainfall, the pollution density, and type and slope of the ground. Also, the time to reach the maximum pollution is almost constant between 3 to 4 hours.}, keywords = {Chemical Pollution,Water Resources,Diffusion of Pollution,GIS,SWMM}, title_fa = {مدلسازی زمان رسیدن آلودگی فسژن اکسیم به حداکثر میزان در رواناب (مطالعه موردی: مناطق مجاور رودخانه کن و شمال سیل ‌برگردان غرب تهران)}, abstract_fa = {آلودگی‌ آب ناشی از مواد شیمیایی به اشکال مختلف مانند بمب­های شیمیایی، حملات تروریستی و اتفاقات ناخواسته یکی از نگرانی­های اصلی جوامع بشری است. آلودگی­های شیمیایی می­تواند به­دلیل نشت مواد آلاینده در سطح زمین یا بارندگی در زمان آلوده­بودن هوا همراه با باران وارد آب شوند. هدف اصلی این تحقیق مدل­سازی زمان رسیدن آلودگی آب­های سطحی به حداکثر مقدار خود پس از ورود آلودگی شیمیایی به آن   می­باشد. در این تحقیق، پخش آلودگی شیمیایی ناشی از عامل تاول­زای فسژن­اکسیم با استفاده از نرم­افزارهای ArcGIS و SWMM در کلیه مناطق مجاور رودخانه کن و شمال سیل ‌برگردان غرب تهران مدل­سازی شده است. نتایج حاصل از این پژوهش نشان می­دهد که میزان حداکثر غلظت آلودگی به دوره بازگشت بارندگی، غلظت آلودگی و نیز جنس و شیب زمین بستگی دارد و همچنین، زمان رسیدن به حداکثر میزان آلودگی تقریباً ثابت و بین 3 تا 4 ساعت است.}, keywords_fa = {ی شیمیایی,منابع آب,پخش آلودگی,سامانه‌های اطلاعات جغرافیایی,SWMM}, url = {https://adst.ihu.ac.ir/article_204171.html}, eprint = {https://adst.ihu.ac.ir/article_204171_f27be658bbc1b263a00716a978b0309d.pdf} } @article { author = {ghaffarpour, reza and jam, alireza and ranjbar, alimohammad}, title = {Optimal Mix of Distributed Generation Allocation to Improve the Security of Energy Supply in Defensive Sites Using Principles of Passive Defence}, journal = {Journal of Advanced Defense Science & Technology}, volume = {7}, number = {1}, pages = {19-32}, year = {2016}, publisher = {Imam Hussein University}, issn = {2676-2935}, eissn = {2980-8022}, doi = {}, abstract = {Security of electrical energy supply in defencive sites is affected by different parameters like natural disasters and enemy attacks. So, attention to principles of passive defence for design and enhancement of electrical networks in defencive sites is critical. The objective of this study is to increase security of energy supply in defencive sites from the standpoint of passive defence. Due to the presence of DG units and the uncertainty of their power, common methods of security evaluation of energy supply are not applicable directly. For this propose, a new framework for optimal allocation of hybrid energy resources in these sites is presented so that networks technical constraints is satisfied beside energy resources uncertainty and sensitive loads priorities. Supply adequacy of consumers is evaluated by solving a set of optimal power flow equations. Finally, a comprehensive algorithm based on imperialist competitive algorithm, scenario reduction, and optimal power flow is proposed. The optimization problem is formulated as combination of a mixed integer nonlinear programming main problem and a set of nonlinear programming sub problems, taking into consideration the system constraints during all computational steps. The proposed model is presented in MATLAB and GAMS environments and optimal mix of energy resources is obtained to increase energy security of defensive sites and to reduce outage of critical loads, towards principles of passive defense (proliferation, diversification, and dispersation). Final results show the effectiveness of the proposed algorithm in optimal design of hybrid energy resources and remarkable improvement of energy supply security.}, keywords = {Passive Defense,Energy Security,Optimal Power Flow,Renewable Energy,Imperialist Competitive Algorithm}, title_fa = {انتخاب ترکیب بهینه منابع تولید پراکنده به‌منظور افزایش امنیت انرژی در سایت‌های دفاعی با رویکرد پدافند غیرعامل}, abstract_fa = {امنیت انرژی الکتریکی سایت­های دفاعی تحت تأثیر عوامل مختلفی از جمله حوادث طبیعی و حملات دشمن قرار دارد. از این­رو، توجه به اصول پدافند غیرعامل به­منظور طراحی و توسعه شبکه­های الکتریکی در مراکز مهم دفاعی، امری حیاتی است. هدف این مطالعه، افزایش امنیت تأمین انرژی الکتریکی سایت­های دفاعی از دیدگاه پدافند غیرعامل است. با توجه به حضور منابع تولید پراکنده و عدم قطعیت تولید توان آ‌ن­ها، روش‌های متداول بررسی امنیت تامین انرژی به­طور مستقیم قابل اعمال نیستند. در این مقاله یک مدل­سازی جدید برای تعیین ترکیب بهینه منابع انرژی ترکیبی (تعیین نوع، ظرفیت و محل نصب مناسب) در مراکز حساس تدوین شده ­است، به‌طوری­که قیود فنی شبکه در کنار عدم قطعیت منابع انرژی و اولویت قطع بارهای حساس برآورده شوند. کفایت تأمین انرژی مصرف‌کنندگان با حل مجموعه‌ای از مسئله‌های پخش بار بهینه مورد ارزیابی قرار گرفته ‌است. الگوریتم ارائه­شده به­منظور حل مسئله مبتنی بر الگوریتم رقابت استعماری، کاهش سناریو و پخش بار بهینه، ارائه شده ‌است. مدل ارائه­شده در محیط نرم‌افزارهای MATLAB و GAMS حل شده ‌است و ترکیب بهینه منابع انرژی برای افزایش امنیت انرژی سایت‌های دفاعی و کاهش میزان خاموشی بارهای حساس، در راستای تحقق اصول پدافند غیرعامل (متعددسازی، متنوع‌سازی و پراکنده‌سازی)، به­دست آمده­است. نتایج نهایی نشان‌دهنده کارایی الگوریتم پیشنهادی در طراحی مناسب منابع انرژی ترکیبی و افزایش قابل توجه امنیت تأمین انرژی الکتریکی است.}, keywords_fa = {اصول پدافند غیرعامل,امنیت انرژی سایت‌های دفاعی,پخش بار بهینه اصلاح‌شده,الگوریتم رقابت استعماری}, url = {https://adst.ihu.ac.ir/article_204172.html}, eprint = {https://adst.ihu.ac.ir/article_204172_ad591dc3a35725b0f65048269763a544.pdf} } @article { author = {jafari, seyed sajad and feli, saeid and ranjbaran, milad}, title = {Analysis of Normal Impact on Sandwich Panel with Considering Difference Energy Absorption Mechanisms}, journal = {Journal of Advanced Defense Science & Technology}, volume = {7}, number = {1}, pages = {33-43}, year = {2016}, publisher = {Imam Hussein University}, issn = {2676-2935}, eissn = {2980-8022}, doi = {}, abstract = {In this paper, a new analytical model has been presented for energy absorption calculation of aluminum-foam sandwich panels under high velocity impact. The panels consist of foam core sandwiched between two aluminum skins. In analytical model, cylindrical rigid projectile with flat ended has been considered. In the quasi-static loading, by using the springs-mass model, energy absorption of aluminum skins with considering difference energy absorption mechanisms has been calculated. Also foam absorbed a partial of projectile energy by crushing. Energy absorption of aluminum-foam sandwich panel was calculated and energy balancing equation has been employed for determination the ballistic limit and residual velocity of projectiles. The results of ballistic limit and residual velocity computed by new model presented good agreement with experimental and numerical results. Also the effects of foam density, projectile mass and diameter in energy absorption of sandwich panel has been investigated.}, keywords = {Sandwich Panel,Foam,Aluminum,Perforation,Energy Absorption}, title_fa = {تحلیل ضربه عمودی در سازه ساندویچی با درنظرگرفتن مکانیزم‌های مختلف جذب انرژی}, abstract_fa = {هدف این مقاله ارائه روش تحلیلی جدیدی برای محاسبه میزان جذب انرژی ورق­های ساندویچی آلومینیوم- فوم تحت اثر ضربه سرعت ‌بالا است. ورق­های ساندویچی آلومینیوم- فوم دارای هسته از جنس فوم هستند که بین دو صفحه فلزی آلومینیومی، محصور شده است.        ضربه­زننده به‌صورت پرتابه صلب استوانه­ای سر تخت در نظر گرفته شده است. با استفاده از مدل جرم و فنر، جذب انرژی لایه­های آلومینیومی در بارگذاری شبه ­استاتیکی و با در نظر گرفتن مکانیزم­های مختلف جذب انرژی محاسبه شده است. همچنین فوم نیز به­واسطه خردشدن بخشی از انرژی پرتابه را جذب می­کند. نهایتاً جذب انرژی توسط ورق­های ساندویچی آلومینیوم- فوم محاسبه و با استفاده از موازنه انرژی، سرعت حد بالستیک و سرعت باقیمانده پرتابه محاسبه شده است. مقادیر سرعت حد بالستیک و سرعت باقی­مانده محاسبه‌شده با روش تحلیلی هم‌خوانی مناسبی با مقادیر تجربی و عددی دارد. همچنین اثرات چگالی فوم، جرم و قطر پرتابه در میزان جذب انرژی ساندویچ پانل بررسی شده است.}, keywords_fa = {ورق ساندویچی,فوم,آلومینیوم,سوراخ شدن,جذب انرژی}, url = {https://adst.ihu.ac.ir/article_204173.html}, eprint = {https://adst.ihu.ac.ir/article_204173_55ea3939959afc5ca01c1393c2405544.pdf} } @article { author = {سروقد مقدم, علیرضا and Sarvghadmoghadam, A. R. and Ziaei, M.}, title = {Vulnerability Analysis Concrete Tanks Liquid Storage under Air Blast}, journal = {Journal of Advanced Defense Science & Technology}, volume = {7}, number = {1}, pages = {45-58}, year = {2016}, publisher = {Imam Hussein University}, issn = {2676-2935}, eissn = {2980-8022}, doi = {}, abstract = {According to the strategic geographic position of  IRAN with the probability of terrorist threats and air strikes, and also the important crucial role of the tanks, their construction by taking passive defense measures and considerations is necessary. Because of few researches on the vulnerability of tanks against the loads due to explosion, investigate the importance of this type of structures against blast loads is increasing. In present study a hypaethral cylindrical concrete tank, exposed to air blasting by one cubic explosive TNT with weight of 352.08 kg has been modeled. The tank is modeled in four situations such as: empty state, ,  and  of body height full of liquid. The results of simulation showed that damages of compressive and tensile in the empty tank are more critical than other modes, and the manner of hypaethral concrete tanks against explosive loads is different from their manner against seismic loads caused by the earthquake. It was also shown that the conwep method has considerate only the effects of the explosion and at least 25% reduction achieved in compressive damage compared with the results of the AUTODYN. The results of this study can be used in retrofitting and safe design of fluids storage tanks to resistance against the blast loads.}, keywords = {Independent Sequence Method,Information Rate,Secret Sharing Schemes and Minimal Access Structure}, title_fa = {تحلیل آسیب‌پذیری مخازن بتنی ذخیره سیال تحت اثر انفجار هوایی}, abstract_fa = {با توجه به نقش حیاتی مخازن و موقعیت جغرافیایی و استراتژیک کشور که همواره در معرض خطر حملات هوایی و تروریستی است، احداث مخازن با در نظر گرفتن اقدامات و ملاحظات پدافند غیر عامل، ضرورت پیدا می کند. از آنجایی که در زمینه آسیب پذیری مخازن در برابر بارهای ناشی از انفجار، پژوهش های چندانی صورت نگرفته است، اهمیت بررسی این نوع سازه ها در برابر بارهای انفجاری افزایش می یابد. در پژوهش حاضر مخزن بتنی استوانه ای، تحت انفجار هوایی ماده منفجره مکعبی شکل به وزن 352.08 کیلوگرم TNT مدل شده است. مخزن در چهار حالت خالی، 1/4، 1/2 و 3/4 ارتفاع بدنه مخزن حاوی سیال آب مدل شده است. نتایج حاصل از شبیه سازی نشان داد که، آسیب های فشاری و کششی در مخزن خالی نسبت به حالت های دیگر بحرانی تر بوده و رفتار مخازن بتنی در برابر بارهای انفجاری، متفاوت از رفتار آنها در برابر بارهای لرزه ای ناشی از زلزله می باشد. همچنین نشان داده شد که روش conwep فقط اثرات رو به انفجار را لحاظ کرده و نسبت به نتایج حاصل از AUTODYN، حداقل 25 درصد کاهش را در آسیب فشاری نشان می داد. از نتایج حاصل از این تحقیق می توان در مقاوم سازی و نیز طراحی ایمن مخازن ذخیره سیال برای مقاومت در برابر بارگذاری انفجاری استفاده نمود.}, keywords_fa = {مخزن بتنی استوانه ای,انفجار,آسیب فشاری و کششی,شبیه سازی اجزای محدود,هیدروکد AUTODYN}, url = {https://adst.ihu.ac.ir/article_204174.html}, eprint = {https://adst.ihu.ac.ir/article_204174_f01019e95457b7de13ba9417c9d32ed3.pdf} } @article { author = {Malakzadeh, Abdollah and Zare Kalate, Seyed Reza and Kamjoo, Mohammad Javad}, title = {Simulation of Kerr Lens Behavior in a Ti:Sapphire Oscillator with Symmetric and Asymmetric Resenator}, journal = {Journal of Advanced Defense Science & Technology}, volume = {7}, number = {1}, pages = {59-70}, year = {2016}, publisher = {Imam Hussein University}, issn = {2676-2935}, eissn = {2980-8022}, doi = {}, abstract = {Femtosecond pulse lasers are one of the most widely used lasers. Femtosecond oscillator is first step to generate powerful femtosecond pulses. In this work, the laser beam propagation in an oscillator in symmetric and asymmetric designs without Kerr lens effect inside a Ti:Sa medium was simulated and the cavity stable operation conditions have been obtained. Then, Kerr lens modelocking behavior is simulated and  the situation compensating the beam astigmatism is achieved. Split-step method has been used to obtain the beam intensity change in the Ti:Sa rod and shooting method has been utilized to calculate the beam spot size on the first cavity mirror. Assuming no Kerr lens effect, influence of the cavity length changes in laser beam characteristics is investigated and considering the Kerr lens effect in the laser rod, influence of the rod position in the beam characteristics and beam propagation is simulated. Finally, by considering the simulations results, conditions to achieve soft or hard aperture modelocking are discussed.}, keywords = {Femtosecond,Oscillator,Kerr Lens Effect,Astigmatism,Modelocking,Soft Aperture Modelocking,Hard Aperture Modelocking}, title_fa = {شبیه‌سازی رفتار قفل‌شدگی مد عدسی کر در نوسانگر لیزر تیتانیوم سفایر با کاواک متقارن یا غیرمتقارن}, abstract_fa = {لیزرهای فمتوثانیه از پرکاربردترین لیزرهای فوق کوتاه می‌باشند. انهدام هدایتگر اپتیکی – لیزری، تولید امواج ترا هرتز پرتوان با واگرایی کم و آشکارسازی آن برای تشخیص آلودگی و یا وجود مواد ممنوعه در یک محیط یا همراه یک شخص،‌ طیف‌سنجی فروشکست القایی برای تست محیط از دور بدون حضور فیزیکی در آن، دوربین فمتوثانیه به منظور از کاربردهای لیزرهای فمتوثانیه می‌باشند. نوسانگر فمتوثانیه اولین گام برای تولید پالس‌های فمتوثانیه پر توان می باشد. در این مقاله ابتدا با شبیه سازی انتشار باریکه لیزر در نوسانگر خطی تیتانیوم سفایر با کاواک آینه انحنادار در ساختار متقارن و نامتقارن به روش ردیابی پرتو برای یک باریکه گاوسی بدون در نظر گرفتن اثر عدسی کر در محیط بهره، نقاط پایدار عملکرد لیزر را به دست می‌آوریم، سپس رفتار قفل‌شدگی مدی عدسی کر در آن نوسانگر شبیه‌سازی شده و با ردیابی پرتو توسط ماتریس ABCD، موقعیتی که آستیگماتیسم باریکه را خنثی می‌کند، به دست می‌آوریم. در این شبیه‌سازی از روش تقسیم گام‌به‌گام برای پیدا کردن تغییرات شدت باریکه درون کریستال و از روش تیراندازی برای محاسبه اندازه قطر لکه بر روی آیینه اول کاواک استفاده می‌شود. با انجام شبیه‌سازی بدون در نظر گرفتن اثر عدسی کر تأثیر طول کاواک لیزر بر روی مشخصات پرتوی درون کاواک نشان داده می‌شود، در ادامه با استفاده از نواحی عملکرد پایدار لیزر که در این حالت به‌دست‌آمده‌ و با در نظر گرفتن عدسی کر، تأثیر مکان محیط بهره بر روی انتشار پرتو شبیه‌سازی‌شده است. در انتها نیز با توجه به نتایج شبیه‌سازی شرایط مختلف جهت دستیابی به قفل‌شدگی مدی در حالت‌های روزنه سخت و نرم بررسی می‌گردد.}, keywords_fa = {فمتوثانیه,نوسانگر,قفل‌شدگی مدی,اثر عدسی کر,آستیگماتیسم}, url = {https://adst.ihu.ac.ir/article_204175.html}, eprint = {https://adst.ihu.ac.ir/article_204175_5fb1d99a0f93b751b5d8bbc12bd2dc1e.pdf} } @article { author = {Parsa, Saeed and Gooran Oorimi, Amir}, title = {An Optimal and Transparent Framework for Automatic Analysis of Malware}, journal = {Journal of Advanced Defense Science & Technology}, volume = {7}, number = {1}, pages = {71-80}, year = {2016}, publisher = {Imam Hussein University}, issn = {2676-2935}, eissn = {2980-8022}, doi = {}, abstract = {Malware is the most important security threat in cyberspace. Some statistics show that over 315,000 malware are released, every day. Certainly, it is not possible to analyze all of these malware, manually. That's why the security vendors are obliged to use software capable of analyzing suspicious executable files. These software determine behavior of suspicious files automatically. Several tools such as Anubis and Cuckoo are produced in this area. The problem of these tools is lack of transparency. Some malware use this sort of weaknesses to recon analysis environments. To resolve this problem some solutions using hardware-assisted virtualization is presented. However, these solutions impose a great run time overhead on the program execution. In this paper an automated malware analysis framework is presented that is both transparent and optimal. This framework in addition to being resistant to malware with split personality features, may also be used to analyze the large amount of malware released every day without adding extra hardware resources. This framework uses dynamic analysis approaches with hardware assisted virtualization technology to analyze suspicious code. The dynamic analysis approaches used in this framework include sandboxing and system calls sequence analysis. Analysis based on hardware-assisted virtualization technology is applied to provide transparent analysis environment.}, keywords = {Analysis Environment,Hardware-Assisted Virtualization,Transparency,Dynamic Analysis,Malware}, title_fa = {یک چارچوب بهینه و شفاف برای تحلیل خودکار بدافزار}, abstract_fa = {بدافزار مهم‌ترین عامل تهدیدات امنیتی در فضای مجازی است. میزان این بدافزارها به حدی است که برخی آمارها نشان می‏دهد روزانه بیش از 315000 بدافزار جدید منتشر می‏شود. مطمئناً تحلیل دستی این حجم از بدافزار غیرممکن است. به همین دلیل باید از نرم‏افزارهایی استفاده شود که توان تحلیل فایل‏های مشکوک را داشته و بتوانند رفتار داخلی آن را به‌طور کاملاً خودکار تعیین نمایند. تاکنون چندین ابزار همانند آنوبیس و جعبه‏شن کوکو در این زمینه ارائه شده‏اند. مهم‏ترین مشکل این ابزارها عدم شفافیت است. امروزه بدافزارهایی منتشر شده‏اند که از این مشکل موجود در ابزارهای کنونی سوءاستفاده کرده و به‌صورت چندشخصیتی عمل می‏کنند. برای حل این مشکل راهکار مجازی‏سازی به­کمک سخت‏افزار ارائه‌شده است، اما این راه حل نیز دارای مشکل عدم بهینگی است. در این مقاله چارچوب تحلیل خودکار بدافزاری ارائه خواهد شد که شفاف و بهینه باشد. بنابراین علاوه­بر این­که در برابر بدافزارهای چندشخصیتی مقاوم است، توان تحلیل این میزان بدافزار منتشرشده در روز را بدون نیاز به اضافه­کردن منابع سخت‏افزاری جدید دارد. این چارچوب از تحلیل پویا به­همراه فناوری مجازی‏سازی به­کمک سخت‏افزار استفاده می‏کند. در تحلیل پویا از روش‏هایی همانند جعبه شن و دنبال­کردن فراخوانی‏های سیستمی استفاده شده است. تحلیل‏های مبتنی بر مجازی‏سازی به­کمک سخت‏افزار نیز برای ایجاد شفافیت مورد استفاده قرار گرفته است.}, keywords_fa = {محیط تحلیل,مجازی‏سازی به کمک سخت‏افزار,شفافیت,تحلیل پویا,بدافزار}, url = {https://adst.ihu.ac.ir/article_204176.html}, eprint = {https://adst.ihu.ac.ir/article_204176_c68e2476ad2d6ee8f1cd1aff53182fe3.pdf} } @article { author = {R. Danaee, M.}, title = {An MCMC-baesd Particle Filter for Multitarget Tracking within Raw Measurements}, journal = {Journal of Advanced Defense Science & Technology}, volume = {7}, number = {1}, pages = {81-94}, year = {2016}, publisher = {Imam Hussein University}, issn = {2676-2935}, eissn = {2980-8022}, doi = {}, abstract = {This paper examines multitarget tracking within raw measurements which has always been considered to be a hassle. This was achieved by separating the state space model of each target into linear and nonlinear subspaces. Then, the Rao–Blackwellization principle was utilized to derive the optimum importance density for special kind of sensor which generates both split and merged measurements within a pixelized observation area. To relieve the complexity associated with the achieved optimum importance, the Gibbs sampler, the well-known sampler from MCMC family, is used to sample from the optimal importance density. The synthetic multitarget tracking scenario using raw data will then be used to show that our new Gibbs sampling method could reach a compromise between accuracy of tracking and computational expense. The proposed idea is motivating to be used in applications where sampling from the optimum proposal density is practically impossible. }, keywords = {Multitarget tracking,Gibbs Sampler,Rao–Blackwellization,Optimal Importance Density,Particle Filter}, title_fa = {فیلترذره مبتنی برMCMC به منظور ردگیری چندهدفه در میان مشاهدات خام و آشکارنشده}, abstract_fa = {در این مقاله به مسئله پرچالش ردگیری چندهدفه در میان داده­های آشکارنشده پرداخته می­شود. برای انجام این کار، ابتدا با تقسیم فضای حالت به دو زیر فضای خطی و غیرخطی و با به­کارگیری اصل Rao–Blackwellization، چگالی اهمیتی بهینه را برای نوع خاصی از مدل سنسور، که مشاهدات منشعب و در هم ادغام­شده را برای ناحیه مشاهده مشبک­شده تولید می­نماید، به­دست آمد. در ادامه، برای کاهش پیچیدگی محاسباتی نمونه برداری از چگالی اهمیتی بهینه، از معروف­ترین نمونه­بردار خانواده MCMC یعنی نمونه­بردار Gibbs برای نمونه­برداری از چگالی اهمیتی بهینه استفاده شد و سپس با مقایسه عملکرد این دو در یک محیط ردگیری چندهدفه و در میان مشاهدات خام و آشکارنشده، نشان داده شد که نمونه­بردار Gibbs به مبادله­ای بین کاهش حجم محاسبات و میزان دقت در ردگیری دست می­یابد. ایده مطرح­شده را می­توان به­عنوان جایگزین برای مواقعی که نمونه­برداری از چگالی اهمیتی بهینه عملا غیرممکن است، استفاده نمود.}, keywords_fa = {ردگیری چندهدفه,نمونه بردار Gibbs,اصل Rao–Blackwellization,چگالی اهمیتی بهینه,فیلتر ذره ای}, url = {https://adst.ihu.ac.ir/article_204177.html}, eprint = {https://adst.ihu.ac.ir/article_204177_f766a1838f1b97ce4ad72fd4b485c53a.pdf} }